Print This Page

General Specifications

OutlineTF-RACK
Mixing CapacityInput Channels40 (32 mono + 2 stereo + 2 return)
Aux Buses20 (8 mono + 6 stereo)
Stereo Buses1
Sub Buses1
Input channel functions8 DCA Groups
I/OInputs16 mic/line (XLR/TRS combo) + 1 stereo line (RCA pin)
Outputs16 (8 XLR + 8 TRS phone)
Expansion slots1 (for NY64-D)
On-board processorsDSP8 Effects + 10 GEQ
General specificationsTF-RACK
Sampling frequency rateInternal48 kHz
Signal delayLess than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz
FaderResolution = 10-bit, +10 dB to –138 dB, –∞ dB all faders
Total harmonic distortionLess than 0.05% 20 Hz–20 kHz @+4 dBu into 600 Ω, INPUT to OMNI OUT, Input Gain=Min. (Measured with a –18 dB/octave filter@80 kHz)
Frequency response+0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT
Dynamic range110 dB typ., DA Converter, 108 dB typ., INPUT to OMNI OUT, Input Gain=Min.
Hum & noise levelEquivalent input noise–128 dBu typ., Input Gain=Max. (Measured with an A-Weight filter)
Residual output noise–85 dBu, ST master off (Measured with an A-Weight filter)
Crosstalk–100 dB (Measured with a –30 dB/octave filter@22 kHz), adjacent INPUT/OMNI OUT channels, Input Gain=Min.
Power requirements100–240 V 50/60 Hz
Power consumption85 W
DimensionsW480 mm (18-7/8 in)
H132 mm (5-1/4 in)
D409 mm (16-1/8 in)
Net weight9.2 kg (20.3lb)
AccessoriesQuick Guide, Power Cord NUENDO LIVE (DAW Software), Rubber stoppers(4)
OptionsAudio Interface Card (NY-64D), Foot Switch (FC5)
OthersOperating temperature range: 0–40 °C, Storage temperature range: -20–60 °C

Recording/ Playback

PC/Mac (USB2.0) Recording 34 tracks, Playback 34 tracks
USB Storage Device Recording 2 tracks (USB hard drive/ SSD)*, Playback 2 tracks (USB hard drive/ SSD/ thumb drive)

*Please note - USB thumb drives are not supported by TF for recording purposes. Please refer to this link for compatible hard drives.

Analog input characteristics

Input Terminals GAIN Load
Impedance
For Use With
Nominal
Input Level Connector balanced /
Unbalanced
Sensitivity*1 Nominal Max. before clip
INPUT1-16 +66dB 7.5KΩ
50-600Ω Mics
or 600Ω Lines
-82dBu (61.6μV) -62dBu (0.616mV) -42dBu (6.16mV) Combo Jack (XLR-3-31 type *2
or TRS phone *3)
Balanced
-6dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
ST IN 10kΩ 600Ω Lines -30dBV (31.6μV) -10dBV (316mV) +10dBV (3.16V) RCA Pin Jack Unbalanced

*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
*4. In these specifications, 0dBu = 0.775Vrms.
*5. +48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.

Analog output characteristics

Output Terminals Source
Impedance
For Use With
Nominal
Output Level Connector balanced /
Unbalanced
Nominal Max. before clip
OMNI OUT 1-8 75Ω 600Ω Lines
+4dBu (1.23 V) +24dBu (12.3 V) XLR-3-32 type *1 Balanced
OMNI OUT 9-16 TRS Phone Jack *6
PHONES *5 100Ω 40Ω Phones 3mW 75mW Stereo Phone Jack (TRS) *2 Unbalanced

*1. 1: GND, 2: HOT, 3: COLD
*2. Tip: LEFT, Ring: RIGHT, Sleeve: GND
*3. In these specifications, 0dBu = 0.775Vrms.
*4. All output DA converters are 24bit, 128times oversampling.
*5. The position of the level control is lowered by 16dB from the maximum.
*6. Tip: HOT, Ring: COLD, Sleeve: GND

Digital input/output specifications

Terminals Format Data length Audio Connector
USB (TO HOST) USB 24bit 34ch input / 34ch output, PCM USB (B type)
iPad USB Playback: MP3 or WAV file data / Record: WAV file data
USB (A type)

 

Control I/O specifications

Terminals Format Level Connector
NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45
FOOT SW TS Phone

 

Return to Top