Print This Page

CL1 Firmware V1.70-2 (Previous version)

Important Notice

  • Please do not use the EEE function (*) of network switches in a Dante network.
    Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts.
    Therefore we strongly recommend that:
  • 1. If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
    2. If you use unmanaged switches, make sure to not use network switches that support the EEE function, since EEE operation cannot be disabled in these switches.
    * EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.

  • You need to update the Dante-MY16-AUD firmware to V3.3.9 or later before using the Dante-MY16-AUD with the CL series firmware V1.51.
  • Dante Firmware Update Manager v1.4.5.7 included in zip files for CL/R series firmware V1.70 does not support Mac OS X 10.6.8.
    Please use Mac OS X 10.7.5, 10.8.5 or 10.9. Or use Windows XP, 7 or 8.

CL/QL/R Compatibility

Please make sure to use appropriate version of CL Editor which is compatible with your CL firmware in reference to the following compatibility chart. Using an unsupported Editor/firmware combination may result in unexpected behavior.

CL Editor CL Firmware QL Firmware R Series Firmware
MAIN SUB DANTE MAIN DANTE MAIN DANTE
1.7.0 1.70 1.70 3.7.1.10 - 3.4.9.3 - 1.2.1 1.02 3.7.1.10 - 3.4.9.3 - 1.2.1 1.70 3.7.1.10 - 3.4.9.3 - 1.2.1
1.01
1.5.1 1.61 1.61 3.6.4.20-3.4.3.8-1.1.3 - - 1.61 3.6.4.20-3.4.3.8-1.1.0
1.5.1, 1.5.0 1.51 1.50 1.51, 1.50
1.1.4 1.15 1.15 3.6.4.20 - 3.4.3.8 - 1.1.0 1.15
1.14 1.14 3.6.4.7 - 3.4.2.1 - 1.0.8 1.14 3.6.4.7 - 3.4.2.1 - 1.0.8
1.1.0 1.12 1.12 1.11
1.11
1.0.0 1.04 1.04 3.6.3.0 - 3.4.1.0 - 1.0.4 1.02 3.6.3.0 - 3.4.1.0 - 1.0.4
1.03 1.02
1.02

Main Revisions and Enhancements

New Features

  • The Scene Memories, Libraries and Setup settings of a CL-series unit can now be saved/loaded individually from a USB flash drive.
  • When switching input patches, you can now choose whether the HA settings of the patched ports continue to be used or the HA settings of the channels are copied to the ports.
  • Sends from an input channel to a bus whose send point is set to PRE can now be assigned to be muted by a DCA group.
  • Extra Metering points have been added to the METER screen.
  • Functions have been added to the GAIN/PAN/ASSIGN knob (assignable encoder) when in SENDS ON FADER mode.
  • In the GAIN/PATCH field of the SELECTED CHANNEL VIEW screen, the analog gain and digital gain of the head amp are both shown at all times.
  • The HPF status of an external head amp such as the R-series is now shown in the GAIN/PATCH field of the SELECTED CHANNEL VIEW screen.
  • Custom fader bank settings can now be stored/recalled individually for each scene.
  • Black has been added as a channel color.
  • The channel display now shows the channel on/off status in SENDS ON FADER mode.
  • You can now select the attributes (latched or unlatched) of an external switch connected to a GPI IN port.
  • It is now possible for Dante-related settings to be initialized when an error occurs on the Dante audio network.
  • In the DCA/MUTE GROUP ASSIGN MODE popup window, you can now assign names to mute groups. In addition, the DCA group name and mute group name can be shown in this popup window.
  • Aviom D800-Dante was added as a Dante device that can be detected and patched by the CL series.
    For details, refer to the CL Firmware V1.70 supplementary manual.

Improvements

  • The limitations on a Dante DEVICE LABEL have been relaxed. Click for details
  • The default value is panned hard LR rather than CENTER when PAN MODE is set to PAN for a ST IN on the CL console.
  • If 15 or more channels are registered in the DCA member indication of the OVERVIEW screen, you can now use the multifunction knobs of the Centralogic section to scroll the channels.
  • A link indicator has been added to the CH LINK MODE popup window, making it easier to determine the currently-assigned link group.
  • The cue monitor level range has been expanded to -30 dB -- +20 dB.
  • In the EFFECT popup window, GEQ popup window, and PREMIUM RACK popup window, you can now use the [SEL] keys to switch channels.
  • If TAP TEMPO is assigned to a user defined key, and you specify the BPM (tempo value) by pressing that key, the BPM value is now shown in a popup window.

Fixed bugs

  • The Windows installer of Dante Firmware Update Manager included in the firmware 'V1.70' zip file does not work due to expiration of the Authenticode certificate. Therefore you cannot install Dante Firmware Update Manager on a Windows PC. We replaced it with the Dante Firmware Update Manager V1.4.7.1 that has fixed this issue. Please use this version for Dante updates. (This installer is compatible with Windows 7 or Windows 8 only.) Please note that Mac OS installer does not cause this problem.
  • Solved a problem in which GPI IN ACTIVE IND. did not function correctly.
  • Solved a problem in which the Balance value of a Mix or Matrix bus was restricted when the Stereo/Mono setting of a bus was switched by RECALL SAFE, FOCUS RECALL, or GLOBAL PASTE, and then switched again.
  • Solved a problem in which executing CH MOVE would cause an incorrect PAN value for the MATRIX of a ST IN.
  • Solved a problem in which the Post On insert on/off setting of a STEREO bus was not always correctly applied to MATRIX SEND 2--8.
  • Solved a problem in which the warning message "DANTE RESOURCE OVERFLOW" inappropriately appeared when a Dante device was powered-on or when the patch was changed significantly.
  • Solved a problem in which the Dante latency of the CL/R series unit differed from the setting of the actual unit, and would not go below 1.0 ms.
  • Solved a problem in which the SYSTEM indicator would not go dark when an error message shown in the Rio field of the I/O DEVICE screen (SYSTEM indicator blinking or lit) switched to a warning message (SYNC indicator blinking or lit).

Known issue

  • If the Dante Virtual Soundcard (DVS) is patched to the CL series device using Dante Controller, the patching may not be recalled correctly when the CL series device is restarted. Patch DVS again. In addition, when using a version of DVS for Windows that is older than v3.2.0, the patch after CH41 cannot be performed from CL series consoles.
  • If the setup of REDUNDANT/DAISY CHAIN is changed while the Dante device is not connected with Dante PRIMARY/SECONDARY connectors, no audio signal will pass. Audio will once again pass after the Dante device is connected of after the power for CL has been restarted.
  • Loading of a file created by version V1.15 or older will not include the mount information of Dante devices other than any connected Rios. It is the same when recalling a DANTE INPUT PATCH LIBRARY. Please reset MOUNT, PATCH, and DANTE INPUT PATCH Library data using V1.51 if necessary.
  • In some specific network switching conditions, a CL-series device may link at 100Mbps instead of the expected 1Gbps. This could be due to the self-checking function of some switches. Use the Device Status screen of Dante Controller to check the link speed of each device. If it shows up as 10 or 100, then disconnect the network cable for this device and re-connect it to correct the problem. To avoid the problem in most cases, first allow the network switches to fully boot up before turning the power on for the CL-series devices.

When updating, perform the update as described in the “CL5/CL3/CL1 Update Guide.

NOTICE

  • When setting up the latency in Dante Controller, and there is a discrepancy in latency with the transmit device or the receive device, the largest (slowest) latency setting becomes effective.
  • The following device labels are used for detecting a SUPPORTED DEVICE.
    Y###-**********
    # is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)
    *indicates any desired character (alphabetical uppercase or lowercase, numerals, or -(hyphen) may be used)
    Up to 31 characters including the 'Y' are supported.
    For the R-series, make sure that the ID indicated by Y###- is not duplicated by any other R-series unit, even if it is a different size.

former version information.

CL Firmware V1.70

New Features

  • The Scene Memories, Libraries and Setup settings of a CL-series unit can now be saved/loaded individually from a USB flash drive.
  • When switching input patches, you can now choose whether the HA settings of the patched ports continue to be used or the HA settings of the channels are copied to the ports.
  • Sends from an input channel to a bus whose send point is set to PRE can now be assigned to be muted by a DCA group.
  • Extra Metering points have been added to the METER screen.
  • Functions have been added to the GAIN/PAN/ASSIGN knob (assignable encoder) when in SENDS ON FADER mode.
  • In the GAIN/PATCH field of the SELECTED CHANNEL VIEW screen, the analog gain and digital gain of the head amp are both shown at all times.
  • The HPF status of an external head amp such as the R-series is now shown in the GAIN/PATCH field of the SELECTED CHANNEL VIEW screen.
  • Custom fader bank settings can now be stored/recalled individually for each scene.
  • Black has been added as a channel color.
  • The channel display now shows the channel on/off status in SENDS ON FADER mode.
  • You can now select the attributes (latched or unlatched) of an external switch connected to a GPI IN port.
  • It is now possible for Dante-related settings to be initialized when an error occurs on the Dante audio network.
  • In the DCA/MUTE GROUP ASSIGN MODE popup window, you can now assign names to mute groups. In addition, the DCA group name and mute group name can be shown in this popup window.
  • Aviom D800-Dante was added as a Dante device that can be detected and patched by the CL series.
    For details, refer to the CL Firmware V1.70 supplementary manual.

Improvements

  • The limitations on a Dante DEVICE LABEL have been relaxed. (Click for details)
  • The default value is panned hard LR rather than CENTER when PAN MODE is set to PAN for a ST IN on the CL console.
  • If 15 or more channels are registered in the DCA member indication of the OVERVIEW screen, you can now use the multifunction knobs of the Centralogic section to scroll the channels.
  • A link indicator has been added to the CH LINK MODE popup window, making it easier to determine the currently-assigned link group.
  • The cue monitor level range has been expanded to -30 dB -- +20 dB.
  • In the EFFECT popup window, GEQ popup window, and PREMIUM RACK popup window, you can now use the [SEL] keys to switch channels.
  • If TAP TEMPO is assigned to a user defined key, and you specify the BPM (tempo value) by pressing that key, the BPM value is now shown in a popup window.

Fixed bugs

  • Solved a problem in which GPI IN ACTIVE IND. did not function correctly.
  • Solved a problem in which the Balance value of a Mix or Matrix bus was restricted when the Stereo/Mono setting of a bus was switched by RECALL SAFE, FOCUS RECALL, or GLOBAL PASTE, and then switched again.
  • Solved a problem in which executing CH MOVE would cause an incorrect PAN value for the MATRIX of a ST IN.
  • Solved a problem in which the Post On insert on/off setting of a STEREO bus was not always correctly applied to MATRIX SEND 2--8.
  • Solved a problem in which the warning message "DANTE RESOURCE OVERFLOW" inappropriately appeared when a Dante device was powered-on or when the patch was changed significantly.
  • Solved a problem in which the Dante latency of the CL/R series unit differed from the setting of the actual unit, and would not go below 1.0 ms.
  • Solved a problem in which the SYSTEM indicator would not go dark when an error message shown in the Rio field of the I/O DEVICE screen (SYSTEM indicator blinking or lit) switched to a warning message (SYNC indicator blinking or lit).

Known issue

  • If the Dante Virtual Soundcard (DVS) is patched to the CL series device using Dante Controller, the patching may not be recalled correctly when the CL series device is restarted. Patch DVS again. In addition, when using a version of DVS for Windows that is older than v3.2.0, the patch after CH41 cannot be performed from CL series consoles.
  • If the setup of REDUNDANT/DAISY CHAIN is changed while the Dante device is not connected with Dante PRIMARY/SECONDARY connectors, no audio signal will pass. Audio will once again pass after the Dante device is connected of after the power for CL has been restarted.
  • Loading of a file created by version V1.15 or older will not include the mount information of Dante devices other than any connected Rios. It is the same when recalling a DANTE INPUT PATCH LIBRARY. Please reset MOUNT, PATCH, and DANTE INPUT PATCH Library data using V1.51 if necessary.
  • In some specific network switching conditions, a CL-series device may link at 100Mbps instead of the expected 1Gbps. This could be due to the self-checking function of some switches. Use the Device Status screen of Dante Controller to check the link speed of each device. If it shows up as 10 or 100, then disconnect the network cable for this device and re-connect it to correct the problem. To avoid the problem in most cases, first allow the network switches to fully boot up before turning the power on for the CL-series devices.

When updating, perform the update as described in the “CL5/CL3/CL1 Update Guide.

NOTICE

  • When setting up the latency in Dante Controller, and there is a discrepancy in latency with the transmit device or the receive device, the largest (slowest) latency setting becomes effective.
  • The following device labels are used for detecting a SUPPORTED DEVICE.
    Y###-**********
    # is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)
    *indicates any desired character (alphabetical uppercase or lowercase, numerals, or -(hyphen) may be used)
    Up to 31 characters including the 'Y' are supported.
    For the R-series, make sure that the ID indicated by Y###- is not duplicated by any other R-series unit, even if it is a different size.

CL Firmware V1.61

New Features

  • Shure ULX-D Digital Wireless Systems and Yamaha XMV8280-D/XMV8140-D were added as Dante devices which can be detected / patched in the CL series.
    The ULX-D firmware has to be updated to the version that supports this feature. Refer to Shure's website for details.
  • Added the function which allows you to view the status of the CL series and the R series (except Ro8-D) on the screen of the CL series (click for details).
    Each R series unit is required to be assigned to the REMOTE HA on the DANTE SETUP screen in order to view its status from the console.

Improvements

  • When a USB device becomes disconnected because of excessive USB current, the device can now be reconnected without having to restart the CL series (click for details).
  • Improved a problem in which, depending on the connected devices (a condenser microphone or a direct box), a noise was caused when adjusting their input gain from CL series with +48V enabled, at the point (between +17 dB and +18 dB) where the PAD inside HA is switched on or off.
  • Improved the response time of HA for SCENE RECALL, etc.

Fixed bugs

  • Solved a problem in which the CL series or Dante-MY16-AUD may partially lose HA gain control of R series units after being powered on for a long period of time with V1.60 firmware. For this reason, V1.60 firmware was withdrawn from our web site.
  • Solved a problem in which the audio of CL series via Dante may very rarely be interrupted for about 15 seconds with the firmware V1.60 or earlier.
  • Solved a problem in which the date and time could not be set using the TOUCH AND TURN function.
  • Solved a problem in which the LED would not light by pushing a USER DEFINED key, when a SPECIFIC CH of CUE was assigned to the key.
  • Solved a problem in which the response of StageMix (iPad app) was slow, when recalling a scene that has a FADE TIME set.

Known issue

  • If the Dante Virtual Soundcard (DVS) is patched to the CL series device using Dante Controller, the patching may not be recalled correctly when the CL series device is restarted. Patch DVS again. In addition, when using a version of DVS for Windows that is older than v3.2.0, the patch after CH41 cannot be performed from CL series consoles.
  • If the setup of REDUNDANT/DAISY CHAIN is changed while the Dante device is not connected with Dante PRIMARY/SECONDARY connectors, no audio signal will pass. Audio will once again pass after the Dante device is connected of after the power for CL has been restarted.
  • Loading of a file created by version V1.15 or older will not include the mount information of Dante devices other than any connected Rios. It is the same when recalling a DANTE INPUT PATCH LIBRARY. Please reset MOUNT, PATCH, and DANTE INPUT PATCH Library data using V1.51 if necessary.
  • In some specific network switching conditions, a CL-series device may link at 100Mbps instead of the expected 1Gbps. This could be due to the self-checking function of some switches. Use the Device Status screen of Dante Controller to check the link speed of each device. If it shows up as 10 or 100, then disconnect the network cable for this device and re-connect it to correct the problem. To avoid the problem in most cases, first allow the network switches to fully boot up before turning the power on for the CL-series devices.

*If you update the device from the V1.51 firmware, update the both MAIN and SUB firmware. To update the MAIN and SUB firmware, perform operations of only the section “Updating the CL firmware” in the “CL5/CL3/CL1 Update Guide.
If you update the device from other than the V1.51 firmware, update the CL device by following the steps in the “CL5/CL3/CL1 Update Guide.

NOTICE

  • When setting up the latency in Dante Controller, and there is a discrepancy in latency with the transmit device or the receive device, the largest (slowest) latency setting becomes effective.
  • Do not change a device label except for the portions shown below as ******. Portions other than ****** are used for the device recognition from CL series.
    Y###-"manufacture name"-"model name"******
    # is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)
    * indicates any desired character (alphabetical uppercase or lowercase, numerals, or -(hyphen) may be used)
  • The Dante-MY16-AUD card and DANTE ACCELERATOR card will be recognized as a SUPPORTED
    DEVICE if you assign the device label as follows.
    Dante-MY16-AUD: Y###-Audinate-DANTE-MY16******
    DANTE ACCELERATOR: Y###-Yamaha-DANTE-ACCEL*******
    # is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)
    * indicates any desired character (alphabetical uppercase or lowercase, numerals, or -(hyphen) may be used)

CL Firmware V1.60

[Important Notice]
With V1.60 firmware, we found that CL consoles may partially lose HA gain control of R series units after being powered on for a long period of time. We have released the new firmware V1.61 in which the serious problem was fixed, and strongly recommend to update your CL/R series units with V1.61.
We sincerely apologize for the inconvenience.

Firmware V1.51

New Features
  • Supports the Scene Preview function.
  • Supports the Help function.
  • Ri8-D, Ro8-D, NXAMP with NXDT104, etc. were added as Dante devices which can be detected / patched in CL series.
  • Added a CUE LEVEL knob to the CUE popup window, allowing adjustment of the Cue level. This can be assigned to a Custom Fader.
  • Added a HPF type select button to the HPF/EQ popup window (1ch), and the magnitude of attenuation has an option of -12dB/oct or -6dB/oct.

Improvements

- Improved the DANTE SETUP screen (click for details).

With the Dante Setup screen, up to 24 units of any I/O device can now be mounted, and up to 8 of them can be registered as remote HA devices.
If the Rio3224-D units with Unit ID 1/2 are connected, they will be automatically mounted as I/O devices and registered as HA remote devices by the default settings. The other devices need to be manually mounted and registered.
Keep in mind that, according to this Dante Setup enhancement, each setting number of I/O device's Unit ID, Device Mount ID, and Remote HA ID can be different. It is up to the user to make a logical setting.

SETUP
The Console ID can be OFF when 5 or more consoles are connected. However, the normal HA control functionality will be disabled on this console. (Though external HA can still be controlled via Slot 1).

DEVICE MOUNT
Mount up to 24 units of any I/O devices manually here. Online devices and offline devices can be chosen, as well as multiple DVS units.
The Unit ID of each device is used only for the device label, such as “Y001” which is a form of identification. These devices can be mounted in any order, regardless of the Unit ID.
Two units of Rio3224-D and a single DVS are automatically mounted by default.

Note:
In order to mount the Dante-MY16-AUD card or the Dante Accelerator card as Supported Device, its device label must be changed via Dante Controller as follows:
Dante-MY16-AUD: Y###-Audinate-DANTE-MY16******
DANTE-ACCEL: Y###-Yamaha-DANTE-ACCEL*******
### is a Unit ID 000–FFF (3-digit hexadecimal number) containing the digits 0–9 and uppercase A–F.
* indicates any desired character (alphabets, numerals, or -)

REMOTE HA ASSIGN
Register up to 8 units of HA remote devices manually from the 24 units of I/O devices in the DEVICE MOUNT page.
They can be chosen regardless of the Unit IDs or the mount order.
Two units of Rio3224-D are automatically registered by default.

- Added the I/O DEVICE screen, and the Dante device setup function was separated from the VIRTUAL RACK screen (click for details).

The new I/O Device screen, independently from the Virtual Rack screen, allows more flexible control of each I/O device.

DANTE PATCH
Lists 24 units of the I/O devices mounted in the Dante Setup.
Dante Input Patch routes 64 channels from I/O devices to the CL console. Pressing the AUTO SETUP will automatically patch them in order of the mounted I/O devices.
Touch the I/O device to access the OUTPUT PATCH, which routes the CL Dante outputs to the I/O device’s outputs. 2 units of Rio3224-D are automatically patched by default.

Rio
Shows the information of each of the mounted I/O devices.
The scroll buttons at the lower-left corner switch among the 24 I/O devices.
This also shows the device’s firmware version as well as each channel name of the output ports.

- Integrated function with Nuendo Live now works even with a CL console that is set to an ID other than #1 (click for details).

Any single PC can now be specified for the Nuendo Live integration, regardless of the Console ID or the DVS’s mount order.

DVS
Specify an any single PC with DVS running.
The CL with Console ID #2 to #4 can also specify a DVS. However, control of a single PC cannot be shared with multiple consoles (though audio can be shared).

SPECIFIED IP ADDRESS
When using the Dante Accelerator card instead of DVS, specify the IP address of the PC’s network port and connect it to enable Nuendo Live integration. However, control of a single PC cannot be shared with multiple consoles (though audio can be shared).

Note
  • The Console File Converter supporting CL V1.51 will be released in early March. The conversion to other models from CL V1.51 cannot be performed until then.

CL Firmware V1.15

Fixed Bug
Solved the following problems:
  • CL could not recognize a Dante device if its device label had less than six characters.
  • After editing a number of channel labels for one device in Dante Controller, the network module of the Dante device might need to be repaired by Yamaha service.
  • When the CL was turned on, or when the Wordclock setting was changed, on a rare occasion audio might not output.

CL Firmware V1.14

New Features
  • Added functions for adjusting the brightness and contrast of the channel name displays. The operations are as follows:
    To adjust the brightness:
    1. While holding down the SCENE MEMORY [STORE] key on the panel, turn on the power of the CL unit.
    2. Press the CHANNEL COLOR CALIBRATION button.
    3. Press the [CUE] key or the [ON] key on the top panel to select the indicator for which you want to adjust the brightness.
    Pressing the [CUE] key raises the brightness, and pressing the [ON] key lowers it.
    4. When you have finished adjusting the brightness, press the APPLY button located on the right of the window to confirm the change.
    5. Press the EXIT button.
    The CL unit will start up in normal operating mode.
    To adjust the contrast:
    1. While holding down the SCENE MEMORY [STORE] key on the panel, turn on the power to the CL unit.
    2. Press the CHANNEL COLOR CALIBRATION button.
    3. Hold down the [SEL] key and turn the multi function knob of channel 1 on the Centralogic section.
    Turning the knob to the left lessens the contrast of all channels, and turning it to the right increases the contrast of all channels.
    4. To change the contrast of one channel independently from the others, hold down the[SEL] key of the corresponding channel and press the [CUE] key or the [ON] key.
    Pressing the [CUE] key lessens the contrast, and pressing the [ON] key increases the contrast.
    5. When you have finished adjusting the contrast, press the APPLY button located on the right of the window to confirm the change.
    6. Press the EXIT button.
    The CL unit will start up in normal operating mode.
Improvement
  • The initial brightness value of the channel name display was changed from maximum to an intermediate setting.
Fixed Bug
  • Solved a problem in which sounds were not output from the MY16-ES64, MY16-EX, and MY16-MD64 in Native mode.
  • Solved a problem in which, when a fader was set as the object of Recall Safe and set to a desired value, and the settings of the CL unit were loaded from USB memory, the default fader position value would not be restored.
  • Solved a problem in which Gain Compensation (GC) was set to On and the Input Channel Library setting of GC = Off was recalled, the Analog gain of HA was not reflected correctly.
  • Solved a problem in which a user logs in as an administrator or a guest to other users with the user authentication key saved on the CL unit, and re-logs in as an administrator or a guest again, the authorization would not change accordingly.
  • Solved a problem in which a user for whom Library List operation is restricted has logged in, and other users consequently could not log in by user authentication keys saved on the CL unit.
  • Solved a network problem in which the device detection or the patch configuration recall was too slow in large-scale Dante system.

CL Firmware V1.12

Fixed Bug
  • Fixed a problem in which the CL series device rarely freezes when you record or play back files with the USB memory recorder, after performing specified operations on the console.

    *If you update the device from the V1.11 firmware, update the MAIN firmware only. To update the MAIN firmware, perform operations of only the section “Updating the CL series firmware” in the “CL5/CL3/CL1 Firmware Update Guide.” In step5, the MAIN firmware “MCLP1_12.PGM.” is the file for copying.
    If you update the device from other than the V1.11 firmware, update the CL series device by following the steps in the “CL5/CL3/CL1 Firmware Update Guide.”

CL Firmware V1.11

Improvement
  • Now supports Nuendo Live.
  • Added the GPI functions.
  • Several User Keys can be stored inside the console.
  • Changed the configurations of the DANTE SETUP window.
  • A pop-up massage appears when an I/O rack is newly recognized or removed in the Dante audio network.
  • The maximum of the number of units which can be used simultaneously is as follows:
    - Up to four CL units and up to thirty-two I/O rack units in a Dante audio network.
    - Up to eight I/O rack units which can HA remote in one CL unit.
    - Up to twenty-four I/O rack and Dante device units which can patch to one CL unit.
Fixed Bugs
  • Solved a problem in which the panel controls might occasionally freeze.
  • Solved a problem in which the Gain Compensation parameter settings were changed when a scene memory was recalled.
  • Solved a problem in which the CL series device may not have recognized Rio if the CL series was started before Rio.
  • Solved a problem in which when Dante-MY16-AUD was installed in a slot, it may have been unlocked while the Error LED on Dante-MY16-AUD lit in orange for at least 45 seconds or audio may not have been streamed.
  • Solved a problem in which if Dante-MY16-AUD was set as Slave to External Word Clock, the Sync LED may not have lit in green when the device was turned on.
  • Solved a problem in which when Dante devices (such as Rio) were not connected to the Dante connector of a CL series device, the CL was muted and audio signals were not output.
  • Solved a problem in an environment with two or more CL series devices, in which the following malfunctions may have occurred with the I/O RACK OUTPUT PATCH pop-up window.
    - A port patched to a different CL series device could not be canceled, but a message would appear, indicating that the port could be canceled.
    - When a file was loaded, patching could not be reproduced, even though the WITH DANTE SETUP AND I/O RACK button was on when the file was loaded.
  • Solved a problem in which when devices with the Dante -MY16-AUD were rebooted, recalling patching of CL series devices and Dante-MY16-AUD may have taken several minutes.
  • Solved a problem in which it may not have been possible to store or recall Dante Input Patch settings to or from the library, even if the Dante Controller was used for patching the Dante Virtual Soundcard (DVS) to the CL series device.
  • Improved the performance in which when a preset file was loaded and patch settings were changed while a CL series device and Rio were connected by a Dante audio network, the changes to the patch settings may not have been completed.
  • Improved the performance in which when the word clock or audio bit rate were changed with a CL series device and Rio connected by a Dante audio network, Rio may have been muted and audio may not have been outputted.

CL Firmware V1.04

Fixed Bugs
  • Solved a problem in which the controllers in the top panel and the touch screen may freeze with certain panel operations.
  • Minor bug fixes.

CL Firmware V1.03

Fixed Bugs
  • Solved a problem in which the Channel Name Display may not be shown when the power switch was turned off and on again in a short span.

CL Firmware V1.02

  • first release version (preinstalled version)

License agreement and software

CL1 Firmware V1.70-2 (Previous version)

You also need to download these files.

You are recommended to download these files.

Return to Top