Print This Page

M7CL V3 Editor V3.5.4-3 for Mac OS X 10.13-10.7

Important Notice

Important Notice for Mac OS X Yosemite (10.10) users.

  • The level meters occasionally stop working when the file dialog box is opened. In that case, clicking on an editor window will make them work again.
  • The M7CL V3 Editor is for use with Studio Manager V2 Host and Network Driver. Be sure to use the latest versions of both the Studio Manager V2 Host and Network Driver, Both are available from this site.
  • Use the Editor with the supported firmware listed in the following table.
  • Files saved using later Editor or console versions cannot be loaded into earlier versions.
  • On the Mac, do not execute the Studio Manager Host via Rosetta. The M7CL V3 Editor cannot be added to the Studio Manager via Rosseta.

M7CL V3 Compatibility (Mac)

M7CL Editor Studio Manager V2 Host M7CL Firmware EtherSound Firmware(*2)
3.5.4 2.3.5, 2.3.4 3.56, 3.55, 3.54 0C18
3.5.1 3.52(*1)
3.51
3.5.0 3.50
3.0.5 3.04 0C16

(*1) only for M7CL-48,32, (*2) only for the M7CL-48ES

Main Revisions and Enhancements

New Feature

  • Now supports macOS 10.13.

System Requirements

OS Mac OS X 10.7.x/ 10.8.x/ 10.9/ 10.10.x/ 10.11.x/ masOS 10.12.x/ 10.13.x
CPU Intel Core family proccesor
Memory 1GB or more
HDD 100 MB or more
Display 1024 x 768 pixels or higher
Other Pointing device such as a mouse, Ethernet (100Base-TX/10Base-T) port

former version information.

EditorV3.5.4 for Mac

Fixed bugs
  • Fixed a problem in which the display rectangle of Q of KEY IN FILTER in DYNAMICS of the Selected Channel window differed from the M7CL.

EditorV3.5.1-2 for Mac

Improvement
  • Now provides the uninstaller. (The M7CL V3 Editor has not been changed.) With this uninstaller, M7CL V3 Editor (V3.x.x) of a previous version is also uninstallable.
    Follow the instructions below to uninstall the M7CL V3 Editor.
    1. After the downloaded compressed file is properly extracted, double-click the file "Uninstall M7CL V3 Editor.app"
    2. Follow the on-screen instructions to uninstall the software.

EditorV3.5.1 for Mac

Fixed bugs
  • Fixed a problem in which incorrect settings of delay time and delay on/off of the ports were displayed when the MONITOR OUT L/R/C channels were assigned to the ports in the Output Port window.
  • Fixed a problem in which the Undo operation did not work when the delay time was input with numbers directly in the Output Port window.
  • Fixed a problem in which the Send Point settings could not be edited simultaneously in the Selected Channel window as an Additional View when the MATRIX channels were selected in the Selected Channel window as the Main View.

EditorV3.5.0 for Mac

New features
  • An ALTERNATE FUNCTION has been added to the functions that can be assigned to the User Defined keys.
  • An OUTPUT PORT window in which DELAY, etc. can be set, just as the M7CL console, has been added.
  • The send level to the MATRIX bus can now be adjusted using the SENDS ON FADER in the MIX window and the ST/MONO window.
  • The send position of the signal is sent to the MIX bus and MATRIX bus can now be set to PRE/POST simultaneously.
  • The channel names are now shown on the TO MIX, TO MATRIX, FROM MATRIX, and ST/MONO area in the Selected Channel window.
  • "ATT"can now be selected for LINK PARAMETER in the CHANNEL LINK page.
  • The Selected Channel window can now be opened by double-clicking EQ/DYN1/DYN2 in the Overview window.
  • All patches which are set to the output ports can now be shown at a glance in the PATCH LIST page.
  • The cursor can now be moved using the key when the cursor is located on the channel name.
Improvements
  • Whether or not the STAGE BOX SETUP setting is transmitted to the M7CL-48ES firmware now can be determined when synchronizing with the M7CL-48ES firmware.
  • The External HA page has been added to the RACK window to control an external head amplifier such as the SB168-ES via the Mini-YGDAI card (e.g., MY16-ES64) in slot 1 of the M7CL-48ES.
  • The VIEW switch buttons have been added to the EXT-ES HA page in the Rack window.
  • Multiple output ports can now be assigned in the PATCH LIST page.
  • The PEQ "Q" parameter value goes up to 16.
Fixed Bug
  • Fixed a problem in which the operations from the M7CL V3 Editor were restricted, despite properly connecting the M7CL V3 Editor, when the user whose operations were restricted with User Level settings is logged-in.

EditorV3.0.5 for Mac

  • Release version

License agreement and software

M7CL V3 Editor V3.5.4-3 for Mac OS X 10.13-10.7

You also need to download these files.

You are recommended to download these files.

Return to Top