Print This Page

Nuage I/O Firmware V1.13

Important Notice

  • Please make sure to use the appropriate versions of NUAGE system components which are compatible with each other
  • After you update the Nuage I/O firmware by using NUAGE Workgroup Manager, be sure to manually turn on Nuage I/O again.

NUAGE System Compatibility

Win : Windows 7 SP1 (32-bit/64-bit), Windows 8 (32-bit/64-bit), Windows 8.1 (32-bit/64-bit)

TOOLS for NUAGE Nuendo NUAGE FADER / MASTER Firmware NUAGE I/O Firmware (16D/16A/8A8D) DANTE ACCELERATOR
MAIN MAIN DANTE Firmware Driver
1.5.0 6.5.20
6.0.7
1.05 1.13
1.12
3.7.1.10 - 3.4.9.3 - 1.2.1 2.0.0 2.0.1
1.2.0 6.0.6 - 6.0.7 1.04
1.1.0 6.0.4 - 6.0.5 1.03 1.11
1.09
3.6.4.20 - 3.4.3.8 - 1.1.3 1.0.1
1.0.0
1.0.0
1.0.0 6.0.2 - 6.0.3 1.03
1.02

Mac OS X 10.7.5/ 10.8.x/ 10.9.x

TOOLS for NUAGE Nuendo NUAGE FADER / MASTER Firmware NUAGE I/O Firmware (16D/16A/8A8D) DANTE ACCELERATOR
MAIN MAIN DANTE Firmware Driver
1.5.0 6.5.20 (*1)
6.0.7 (*2)
1.05 1.13
1.12
3.7.1.10 - 3.4.9.3 - 1.2.1 2.5.0
2.5.1
1.2.0 6.0.6 - 6.0.7 1.04 2.5.0(*3)
2.0.0 2.0.0
1.1.0 6.0.4 -6.0.5 1.03 1.11
1.09
3.6.4.20 - 3.4.3.8 - 1.1.3 1.0.1 1.0.1
1.0.0(*4) 1.0.0
1.0.0 6.0.2 - 6.0.3 1.03
1.02
1.0.1(*4) 1.0.1
1.0.0(*4) 1.0.0

*1 Nuendo 6.5.20 does not support OS 10.7.x.
*2 With Nuendo 6.0.7, only some additional features of V1.5.0 are available.
*3 Support only for Mac Pro (Late 2013) / Nuendo 6.0.7.
*4 VST System Link function is not available.

Main Revisions and Enhancements

Main Revisions and Enhancements

Fixed Bugs

  • Solved a problem in which audio was sometimes cut off when the cable of the [PRIMARY] connector was disconnected and then reconnected while Nuage I/O was being used in a redundancy network.
  • Solved some other minor problems.

former version information.

V1.1.2

Fixed Bugs
  • Solved a problem in which an instantaneously noise would occur when, after turning on the power of Nuage I/O, the “Active” indications in the Workgroup would come on for the first time.
  • Solved some other minor problems.

V1.1.1

Fixed Bugs
  • Solved a problem in which Nuage I/O (Nio) would no longer clock correctly if the word clock source is re-connected to the BNC or AES/EBU on the Nuage I/O, after the unit receives a stable clock. Also solved a problem in which (in the above situation) the sample rate LED on the front panel would not flash even though the unit was not clocking properly.
  • Solved a problem in which sync loss may occur among samples between different channels within a Nuage series device or between different Nuage series devices.
  • Solved a problem in which the Input Trim/Output Trim functions of the Nuage I/O 16A or 8A8D, which was adjusted by using NUAGE Workgroup Manager, would not be changed correctly.
Notice
  • Changing the sample rate of Dante Accelerator from Dante Controller sets the same sample rate for Nuendo but not for Nuage I/O(Nio). Please change the sample rate from Nuendo for the Nuage system
  • In order to use the direct monitoring of Nuage I/O, surround processor, and the system link function with SyncStation, please make sure to patch Dante Accelerator and Nuage I/O to follow the ID order from the first Nuage I/O, starting from 1-16, 17-32, then 33-48, and so on.

License agreement and software

Nuage I/O Firmware V1.13

Return to Top