Print This Page

PM1DV2 System Software V2.08 for Win Vista/XP/2000/NT/98SE

Important Notice

  • This firmware update is only valid when installing into PM1D system currently running Version 2 software. If you are running Version 1 system software, you will need to contact your Yamaha Commercial Audio Dealer to purchase the Version 2 upgrade kit.
  • The CS1D cannot be downgraded from System Software Version 2 to Version 1.
  • Be sure to upgrade the PM1D Manager to the same version as the system software. The PM1D Manager and system software versions must be the same.
  • Firmware Composition of System Software Versions

  • The following table shows the firmware versions that constitute the listed versions of the system software.
  • Red numbers indicate firmware versions updated concurrently with the latest version of the corresponding system software.

PM1D System Software Compatibility.

CS1D

System Software
Versions
Firmware Versions
C_HIF C_TCU CMU PS CNL PNL IN01-12 IN13-24 IN25-36 IN37-48 INSEL OUTSEL MAS2 MAS1 METER
2.08 1.80 1.80 2.08 1.00 1.60 2.00 1.60 1.60 1.60 1.60 1.60 1.60 1.60 1.60 2.00
2.05 1.80 1.80 2.05 1.00 1.60 2.00 1.60 1.60 1.60 1.60 1.60 1.60 1.60 1.60 2.00
1.85 1.80 1.80 1.85 1.00 1.60 1.81 1.60 1.60 1.60 1.60 1.60 1.60 1.60 1.60 1.60

DSP1D (EX)

System Software
Versions
Firmware Versions
EMU E_TCU E_HIF UIF PDB GDB IDB1 IDB2 EDB
2.08 1.88 1.80 1.80 1.81 1.83 1.83 1.83 1.83 1.83
2.05 1.85 1.80 1.80 1.81 1.83 1.83 1.83 1.83 1.83
1.85 1.85 1.80 1.80 1.81 1.83 1.83 1.83 1.83 1.83

AI8/AO8

System Software
Versions
Firmware Versions
IN** OUT**
2.08 1.80 1.80
2.05 1.80 1.80
1.85 1.80 1.80

DIO8

System Software
Versions
Firmware Versions
IN** OUT**
2.08 1.80 1.80
2.05 1.80 1.80
1.85 1.80 1.80

* PM1D user data is compatible with higher-numbered system versions, but not with lower system versions.

Known Problem

  • When you assign an empty scene to the Event No.000 in TC EVENT page, CS1D may occasionally hang up depending on the condition. Please make sure to assign an already-stored scene to the Event No.000.
  • When PM1D Manager V2 is running on Windows 7, 02R96 V2 cannot remotely control PM1D V2 system.

Fixed Bug

  • Fixed a problem in which Out/In Port of the Remote Control Setup field could not be selected in the Option popup window, when the PM1D Manager was running on Windows Vista or Windows 7 and a remote controller such as the DM2000 V2 was connected.
  • Fixed a problem in which the [MUTE MASTER] button could not be turned ON/OFF when the SAFE KEY MODE SELECT function was set to [CH+UNIT] in the RECALL SAFE window of the PM1D Manager.
  • Fixed a problem in which the ON/OFF setting of HPF or LPF wasn't matched with the device when PINK NOISE or BURST NOISE was selected for OSC MODE, and an HPF or LPF indication appeared in the OSCILLATOR window of the PM1D Manager.
  • Fixed a problem in which the scene was not recalled properly in the EVENT TRIGGER function in the TC EVENT popup window, when INC or DEC was executed using TIME CODE, after an EVENT set to INTERVAL or MANUAL was recalled.
  • Fixed a problem in which REC LVL and REPR LVL of the copied effect were not linked properly when the effect, for which the type was set to OPENDECK and the MAKE UP parameter was set to On, was copied to another one in the EFFECT ASSIGN window.
  • (only using the DUAL CONSOLE mode)
    • Fixed a problem in which the scene memory protect function could not be switched on/off when the scene memories of Consoles 1 and 2 were not matched.
    • Fixed a problem in which exiting from the PREVIEW mode was sometimes not possible when the scene was stored in PREVIEW mode with Console 2 and the scene was recalled using the SCENE MEMORY [DEC]/[INC] switches of Console 2 before the STORE operation of the Console 1 was completely finished.
    • Fixed a problem in which the undo operation of CONSOLE 1 could not finish when the SCENE MEMORY [RECALL UNDO] switch was pressed twice from Console 1 after storing the scene.
    • Fixed a problem in which the message "MIDI : Rx BUFFER FULL!" might appear when the scene was recalled using the TC EVENT function.
    • Fixed a problem in which the numbers of the FREQ and DELAY parameters were not displayed properly when the tempo was changed using TAP TEMPO while the effect type including the TEMPO parameter was selected.
    • Fixed a problem in which the recall and store functions sometimes could not be executed after the global paste function was executed with multiple scene memories.
    • Fixed a problem in which the numbers of the FREQ and DELAY parameters were not displayed properly when the tempo was changed using TAP TEMPO while the effect type including the TEMPO parameter was selected.
    • Fixed a problem in which the recall and store functions sometimes could not be executed after the global paste function was executed with multiple scene memories.
    • Fixed a problem in which the front panel setting of the Console 2 might not be matched with the setting in the LCD display when the scene was recalled using the TC EVENT function.

System Requirements

OS Windows 7
(32-bit; Ultimate / Professional / Home Premium)
Windows Vista
(32-bit; Ultimate/Enterprise/Business/Home Premium/Home Basic)
Windows XP Professional / XP Home Edition / 2000 / NT 4.0 (Service Pack 6a or later) / Me / 98 / 95
CPU 1.4GHz or higher Intel Core/Pentium/Celeron family processor;
1GHz or higher Intel Core/Pentium/Celeron family processor An IBM PC/AT compatible computer with at least a Pentium II 233 MHz or equivalent CPU (Pentium II 350 MHz or faster is recommended)
Memory 1GB or more 512 MB or more 64 MB or more memory (128 MB or more is recommended)
HDD 10 MB or more
Display 1024 x 768 pixels or higher; High Color 16-bit or higher 800 x 600 pixels and 16 bit color (SVGA, High Color) or higher 800 x 600 pixels (SVGA, High Color) or higher
Other Serial port * You will need an RS-232C cable (cross-wired) not exceeding 5 meters, or a USB cable not exceeding 3 meters.

Depending on your hardware or OS, system requirements may be greater than listed above.

If you are using a notebook computer, system requirements may be greater than listed above as the minimum. Also, communication may become unstable due to the power management settings in the Windows Control Panel, or due to power management settings specific to notebook CPUs (e.g., SpeedStep (Intel Corporation), PowerNow! (AMD Corporation), or LongRun (Transmeta Corporation)). Please disable these power management settings and use your computer with its power supply adaptor connected.

License agreement and software

PM1DV2 System Software V2.08 for Win Vista/XP/2000/NT/98SE

Return to Top