Print This Page

Rio3224-D Firmware V1.15 (Previous version)

Important Notice

  • Please do not use the EEE function (*) of network switches in a Dante network.
    Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts.
    Therefore we strongly recommend that:
  • 1. If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
    2. If you use unmanaged switches, make sure to not use network switches that support the EEE function, since EEE operation cannot be disabled in these switches.
    * EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.

  • This update consists entirely of improvements and bug fixes. It requires an update to the Dante module as well as the internal firmware, so please allow plenty of time when upgrading. If you need advice about the update procedure, please contact your region's Yamaha support line.
  • The [PREVIEW] key and Help functions will be available in future updates.
  • Integrated function with Nuendo Live works only with the CL CONSOLE that is set to ID#1.
  • When multiple PCs running DVS are connected, the CL CONSOLE will only integrate with Nuendo Live on the PC which has the lowest RACK No. on the CL CONSOLE.
  • You need to update the Dante-MY16-AUD firmware to V3.3.9 or later before using the Dante-MY16-AUD with the CL series firmware V1.15.

CL/QL/R Compatibility

Please make sure to use appropriate version of CL Editor which is compatible with your CL firmware in reference to the following compatibility chart. Using an unsupported Editor/firmware combination may result in unexpected behavior.
The Firmware Set is a set of main (and sub) firmware of the device and the Dante firmware. The version of Firmware Set is the same as the version of the main firmware. Refer to the release note of each firmware about the details of the Firmware Set.

CL Series QL Series R Series
Editor Firmware Set Editor Firmware Set Firmware Set
2.0.4 2.0.4 1.08 1.08 2.00
2.0.0 2.03 1.0.3 1.07
1.7.0 1.70 1.02 1.02 1.70
1.01 1.01
1.5.1 1.61 - - 1.61
1.5.1, 1.5.0 1.51 1.51, 1.50
1.1.4 1.15 1.15
1.14 1.14
1.1.0 1.12 1.11
1.11
1.0.0 1.04 1.02
1.03
1.02

R Series Firmware Set

Firmware Set Main Dante
2.00 2.01 3.7.1.10 - 3.4.9.3 - 1.2.1
1.70 1.70
1.61 1.61 3.6.4.20-3.4.3.8-1.1.0
1.51, 1.50 1.51, 1.50
1.15 1.15
1.14 1.14 3.6.4.7 - 3.4.2.1 - 1.0.8
1.11 1.11
1.02 1.02 3.6.3.0 - 3.4.1.0 - 1.0.4

Main Revisions and Enhancements

Fixed Bug

Solved the following problems:

  • CL could not recognize a Dante device if its device label had less than six characters.
  • After editing a number of channel labels for one device in Dante Controller, the network module of the Dante device might need to be repaired by Yamaha service.
  • When the CL was turned on, or when the Wordclock setting was changed, on a rare occasion audio might not output.

Known issues

  • If the Dante Virtual Soundcard (DVS) is patched to the CL series device using the Dante Controller, the patching may not be recalled correctly when the CL series device is restarted. Patch the DVS again.
  • In an environment with two or more CL series devices, the following malfunctions may have occurred with the I/O RACK OUTPUT PATCH pop-up window.
    A port patched to a different CL series device could not be canceled, but a messagewould appear, indicating that the port could be canceled.
  • When the CL was turned on, the patch configuration might not display in Dante Controller. This problem does not affect audio and does not occur frequently. If this problem occurs, patch the devices again in Dante Controller.

License agreement and software

Rio3224-D Firmware V1.15 (Previous version)

Return to Top