Print This Page

RSio64-D Firmware V3.10 (Previous version)

Important Notice

Please do not use the EEE function (*) of network switches in a Dante network.

Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts.

Therefore we strongly recommend that:
  • 1. If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
  • 2. If you use unmanaged switches, make sure to not use network switches that support
  • * EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.

Cautions for Dante Firmware

  • When updating the firmware, follow the instructions described in the “RSio64-D Firmware Update Guide”. You do not need to update the Dante firmware if you update the firmware to V3.10.

CL/QL/R/Tio Series Editor/Firmware Compatibility

Please make sure to use appropriate version of CL Editor or QL Editor which is compatible with your console firmware in reference to the following compatibility chart. Using an unsupported Editor/firmware combination may result in unexpected behavior.
The Firmware Set is a set of main (and sub) firmware of the device and the Dante firmware. The version of Firmware Set is the same as the version of the main firmware. Refer to the release note of each firmware about the details of the Firmware Set.

CL Series QL Series R Series Tio1608-D
Rio/Ri/Ro RMio64-D RSio64-D
Editor Firmware Set Editor Firmware Set Firmware Set Firmware Set Firmware Set Firmware Set
4.1.0 4.10 4.1.0 4.10 4.10 3.11 4.10 1.01
4.0.1, 4.0.0 4.04, 4.02, 4.01, 4.00 4.0.1, 4.0.0 4.04, 4.02, 4.01, 4.00 3.11 3.11, 3.10 3.10,1.00 1.00
3.1.0 3.11, 3.10 3.1.0 3.11, 3.10 3.11, 3.10, 3.00 3.11, 3.10 3.10, 1.00
3.0.0 3.02, 3.01, 3.00 3.0.0 3.02, 3.01, 3.00 3.11, 3.10, 3.00 3.10, 3.00 -
2.0.4 2.04 1.0.8 1.08 3.11, 3.10, 3.00, 2.00 -
2.0.0 2.03 1.0.3 1.07
1.7.0 1.70 1.0.2 1.02 1.70
1.0.1 1.01
1.5.1 1.61 - - 1.61
1.5.1, 1.5.0 1.51 1.51, 1.50
1.1.4 1.15 1.15
1.14 1.14
1.1.0 1.12 1.11
1.11
1.0.0 1.04 1.02
1.03
1.02

R Series Firmware Set

Rio3224-D/Rio1608-D/Ri8-D/Ro8-D

Firmware Set Main Dante
4.10 4.10 3.10.0.19 - 4.0.3.1 - 1.3.2
3.11 3.11 3.8.0.24 - 3.5.1.8 - 1.2.2
3.10 3.10
3.00 3.00
2.00 2.01 3.7.1.10 - 3.4.9.3 - 1.2.1
1.70 1.70
1.61 1.61 3.6.4.20-3.4.3.8-1.1.0
1.51, 1.50 1.51, 1.50
1.15 1.15
1.14 1.14 3.6.4.7 - 3.4.2.1 - 1.0.8
1.11 1.11
1.02 1.02 3.6.3.0 - 3.4.1.0 - 1.0.4

RMio64-D

Firmware Set Main Dante
3.11 3.11 3.8.0.24 - 3.5.1.8 - 1.2.2
3.10 3.10
3.00 3.00
1.00 1.00 3.7.1.10 - 3.4.9.3 - 1.2.1

RSio64-D

Firmware Set Main Dante
4.10 4.10 3.10.0.19 - 4.0.3.1 - 1.3.2
3.10 3.10 3.8.0.24 - 3.5.1.8 - 1.2.2
1.00 1.00

Main Revisions and Enhancements

  • You can remotely control one RSio64-D unit from a maximum of two CL/QL/R Remote units.

Fixed bug

  • Solved a problem in which the correct static IP address is not assigned even if STATIC IP (MANUAL) is selected.

NOTICE

  • When setting up the latency in Dante Controller, and there is a discrepancy in latency with the transmit device or the receive device, the largest (slowest) latency setting becomes effective.
  • The following device labels are used for detecting a SUPPORTED DEVICE.
    Y###-**********
    # is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)
    *indicates any desired character (alphabetical uppercase or lowercase, numerals, or -(hyphen) may be used)
    Up to 31 characters including the 'Y' are supported.
    For the R-series, make sure that the ID indicated by Y###- is not duplicated by any other R-series unit, even if it is a different model.

License agreement and software

RSio64-D Firmware V3.10 (Previous version)

Return to Top