Print This Page

Hardware

What is the maximum number of fiber ports available?

SWP1-8MMF and SWP1-16MMF have one fiber port (opticalCON multimode) as standard, while SWP1-8 has none. Each model has two fiber slots so can be upgraded to have two fiber ports, using the optional fiber module kit MMF-SWP1.

Was this FAQ helpful to you?

Can single-mode fiber modules be installed?

Only the multi-mode fiber module is supported.

Was this FAQ helpful to you?

What does the “STATUS” LED mode show?

Each LED will light or blink when a loop is detected on the port. If there is no loop, the LEDs will be off.

Was this FAQ helpful to you?

What does the “VLAN” LED mode show?

The LEDs are used to indicate the VLAN assignment for each port. For example, if both LEDs are unlit, the port is assigned to VLAN 1. VLAN2 is shown by only the upper LED being lit green, while VLAN3 is shown by an orange upper LED. If both LEDs are lit orange, it indicates that the port is used as a Trunk.

Was this FAQ helpful to you?

What is the CONSOLE RJ45 connector used for?

It is provided for trained IT engineers to use: it is not necessary for normal use. It provides a Command Line Interface (CLI) to manage and configure the switch via serial cable. However, for quick setup, the front panel DIP switches can be used, while a web browser interface provides a convenient additional way to access the switch settings.

Was this FAQ helpful to you?

What is the specification for the back-up external DC input?

24V, 1A. Pin 4 hot, pin 1 GND

Was this FAQ helpful to you?

Configuration

What is the difference between the “DANTE” and “USER” Config modes?

The "DANTE" mode is already optimized for use with a Dante audio network. In other words, the settings such as EEE, QoS, and IGMP Snooping are automatically set for Dante. Use “DANTE” mode in combination with the “VLAN PRESETS” to recall a convenient configuration. These are factory presets, which will be recalled after each reboot.
The "USER" mode memorizes the switch settings, which can be freely edited. For example, use a DANTE VLAN PRESET to begin, export the Config file, switch to USER mode, load the Config file, then edit the VLAN assignments. These settings will be memorized, even after power-off.
Please note that DANTE and USER are completely different modes. Not only the switch configurations, but also the other settings such as administrator password and IP address, are not shared between them.

Was this FAQ helpful to you?

Does the “Normal” VLAN Preset use VLAN 1 for every port?

Yes.

Was this FAQ helpful to you?

How many VLANs are supported by the switch?

Up to 255 VLAN IDs can be defined other than default VLAN 1.

Was this FAQ helpful to you?

Can any of the RJ45 ports be used as a “Trunk”, or only the fiber ports?

VLAN PRESET B uses two etherCON/RJ45 ports as “Trunk” ports, as well as the fiber ports. With the USER CONFIG, any port can be used as a “Trunk”.

Was this FAQ helpful to you?

Can 2 cables be used between a pair of switches to provide a doubled network bandwidth and a redundant connection?

Yes, Link Aggregation is provided with VLAN Preset Normal, A and B. However, this type of redundancy does cause short audio dropouts in the Dante network after a cable failure, so it is recommended to use separate Primary and Secondary Dante networks in critical applications. You can also use Link Aggregation on each separate Primary and Secondary network.

Was this FAQ helpful to you?

How can a user modify the switch settings, program VLANs etc?

Use the Web GUI, which is accessed via the Yamaha LAN Monitor software.

Was this FAQ helpful to you?

How can I use Spanning Tree for a redundant ring network?

The VLAN PRESETS are not suitable for use in a Spanning Tree network, though they can be edited via the Command Line Interface (CLI) to support Spanning Tree. This should only be programmed by experienced network engineers.
In order to skip the programming, the configuration files are provided as variations of the VLAN Presets. Download them from the Yamaha Pro Audio website.

Was this FAQ helpful to you?

Can the SWP1 be used in combination with other makes of switch?

Yes, though it is recommended to use Yamaha switches throughout the network for a more stable environment and better network monitoring facilities. Features such as Link Aggregation and Spanning Tree might not be fully compatible with other makes of switch.

Was this FAQ helpful to you?

Feature-set

Does the switch support EEE (“Energy Efficient Ethernet”)?

Yes, though it is disabled in DANTE CONFIG mode for stable Dante networking.

Was this FAQ helpful to you?

Does the switch support QoS with DSCP?

Yes. It is set up correctly for use with Dante in DANTE CONFIG mode.

Was this FAQ helpful to you?

Does the switch provide IGMP Snooping (V3) for filtering multicast traffic?

Yes. It is enabled in DANTE CONFIG mode. However, note that it is disabled on VLAN 2 of Preset A and B, because VLAN 1 is designed for a Dante network while VLAN 2 is for other network data on these presets.

Was this FAQ helpful to you?

Can the switch be the IGMP Querier?

Yes. It is enabled on the VLANs set up for Dante in DANTE CONFIG mode. If multiple units of SWP1 series are connected, one of them will be automatically elected as the Querier.

Was this FAQ helpful to you?

Does the switch protect against network loops?

Yes. If any loop is discovered, it will be automatically blocked.

Was this FAQ helpful to you?

Does the switch have a static IP address for management purposes?

The switch is set to DHCP by default. In a Dante network without a DHCP server, it will default to using an IP address in the range 169.254.*.*. In the same way as Dante devices, the switch does not rely upon IP addresses to be discovered by the management software (Yamaha LAN Monitor). A static IP address can be assigned to the switch if required.

Was this FAQ helpful to you?

Can the SWP1 act as a DHCP server?

No. It can be a client, but not a server.

Was this FAQ helpful to you?

What security settings does the switch have?

The Web GUI can be protected by a password, to stop unauthorized changes to the settings.

Was this FAQ helpful to you?

Are there any extra security functions to protect additional devices being added to the network?

Port Shutdown and ACL (Access Control List) are available to protect from unwanted access.

Was this FAQ helpful to you?

Yamaha LAN Monitor

Which switches can be used with this software?

SWP1 and SWR series are the main focus for this software. Some other Yamaha switches, router, and wireless AP are also supported, but with limited functionality. Some 3rd party switches will be discovered, but will not be controlled.

Was this FAQ helpful to you?

How does the software discover the switches in the network?

A Layer 2 protocol is used, without any need to take care of the IP addresses. Just select the correct network interface on your computer, then the switches and Dante devices will be discovered automatically.

Was this FAQ helpful to you?

Can the software be used to configure switch settings?

Not directly. This software is primarily used for network monitoring. However, the software does include a short-cut to access the Web GUI, which is used for editing the switch settings.

Was this FAQ helpful to you?

Can each switch be given a name for easy recognition?

Yes, they can be named in the “Device Settings” of Yamaha LAN Monitor.

Was this FAQ helpful to you?

Can USER switch config settings be saved and loaded into other switches of the same type?

Yes, this can be achieved via the Web GUI.

Was this FAQ helpful to you?

Can any programming or editing be made off-line?

Not easily. The only chance is to save the switch config as a .txt file and edit that. Only experienced programmers should attempt that.

Was this FAQ helpful to you?

Can the software be used to edit settings in Dante devices?

No, just monitoring Dante settings such as bandwidth used, latency, and sample-rate. Dante Controller software can be used on the same computer for editing Dante device settings.

Was this FAQ helpful to you?

Can a log file be saved for trouble-shooting purpose?

Yes, a SYSLOG can be output from each switch and saved via the Web GUI.

Was this FAQ helpful to you?

Why do some Dante devices have 2 different MAC addresses and register 2 times in the “Connected Devices” list?

Some Dante enabled devices such as Yamaha CL-series, QL-series and R-series register twice in the Connected Devices list of Yamaha LAN Monitor. This is normal behavior, as these devices have 2 MAC addresses: one for the Dante port and one for device management.

Was this FAQ helpful to you?

What is the “Snapshots” function used for?

Press the “Snapshot” icon to remember the current status of the connected devices. If the status changes at all (if a new device joins the network or if a device leaves the network), the software will notify the user. A new device will be highlighted blue, while a missing device will be highlighted red. That would make troubleshooting quick and easy. If you reconfigure the network, press the Snapshot icon once again to reset the reference.

Was this FAQ helpful to you?

MCP1 controllers do not appear in the “Connected Devices” list.

Start Yamaha MTX-MRX Editor software, or send a PING command to MCP1 and press the Update button in the Connected Devices list of Yamaha LAN monitor. MCP1 will be discovered and displayed.

Was this FAQ helpful to you?

Web GUI

Why is the Web GUI sometimes not able to change the VLAN settings of specific ports?

This is because those ports will be assigned to a Link Aggregation group, and the Web GUI does not currently support the editing of Link Aggregation groups. In this case, either disable the group by using the Command Line Interface, or import a Config file in which Link Aggregation is disabled then change the VLAN settings via the Web GUI.

Was this FAQ helpful to you?

Why is the time setting sometimes cleared by a restart, although it was set by the Web GUI or other command?

Since the SWP1 does not maintain the clock time during power-off, the day and time setting will be initialized to "1970/1/1 0:00:00” each time the device is restarted. A Network Time Protocol (NTP) server is needed to automatically update the device’s time settings.

Was this FAQ helpful to you?

Why doesn’t the Syslog show the actual date and time on the Web GUI dashboard?

Since the SWP1 does not maintain the clock time during power-off, the day and time setting will be initialized by each restart. Therefore, the current Web GUI version shows the logs with "elapsed time since restart" regardless of the time setting.

Was this FAQ helpful to you?

Return to Top