Print This Page

Specifications

OutlineEMX5016CF
Mixing capabilityMixing channels8 Mono + 4 Stereo +2 Return
AUX4 (incl. 2x Effect Send)
MAINStereo
Input channel functionsCH1-8: HPF, Compressor, 3-band mid-sweep PEQ Insert I/O; CH9-16: HPF, 3 band PEQ
On-board processors2x SPX, 2x Digital 9-band GEQ, Feedback suppressor, Frequency response correction, Maximizer, YSProcessing
I/OMic inputs12
Phantom power+48V DC; ON/OFF
Line inputs4x Stereo
Control and others2x Foot switch, Lamp
On-board amplifiersMaximum output power @4ohms500W/ch
Maximum output power @8ohms370W/ch (100V model), 350W/ch (120V model), 320W/ch (220-240V model)
Output selection500W, 200W, 75W; L/R, AUX1/MONO, AUX1/AUX2
General specificationsEMX5016CF
Total harmonic distortionLess than 0.3%
Frequency response0, +0, -3dB 20Hz-20kHz
Hum & noise levelEquivalent input noise-128dBu
Residual output noise-68dBu (Speaker out); -95dBu (Line out)
Crosstalk-68dB
Protection circuitLoad protectionPower switch on/off mute, DC-fault (power supply shutdown/manual reset), Clip limiter (≧THD 1%; compression)
Amplifier protectionThermal (heatsink temp ≧90 degrees celsius; output mute/auto reset), Vl limiter (RL ≦2ohms)
Power supply protectionThermal (heatsink temp ≧100 degrees celcius; power supply shutdown/manual reset)
Cooling2x Variable-speed fan
Power requirementsDepend on area of purchase; AC100V, 120V or 220-240V; 50/60Hz
Power consumption500W
DimensionsW444mm; 17-1/2in
H155mm; 6-1/8in
D493mm; 19-7/16 (12U)
Net weight11kg; 24.3lbs
AccessoriesOwner’s Manual, AC power cord

Input characteristics

Input terminal PAD GAIN Actual load impedance For use with nominal Input level Connector
Sensitivity Nominal Max. before clip
CH INPUT A 1-8 0dB -60dB 3kohms 50-600 ohm Mics -80dBu -60dBu -40dBu XLR-3-31 type *3
-16dB -36dBu -16dBu +4dBu
26dB -34dB -54dBu -34dBu -14dBu
+10dB -10dBu +10dBu +30dBu
CH INPUT B 1-8 0dB -60dB 10kohms 600ohm Lines -80dBu -60dBu -40dBu TRS phone jack
-16dB -36dBu -16dBu +4dBu
26dB -34dB -54dBu -34dBu -14dBu
+10dB -10dBu +10dBu +30dBu
ST CH MIC INPUT
9/10-15/16
-60dB 3kohms 50-600 ohm Mics -80dBu -60dBu -40dBu XLR-3-31 type
-16dB -36dBu -16dBu -10dBu
ST CH LINE INPUT
9/10-15/16
-34dB 10kohms 600ohm Lines -54dBu -34dBu -14dBu Phone jack,
RCA pin jack
+10dB -10dBu +10dBu +30dBu
CH INSERT IN (1-8) - 10kohms 600ohm Lines -20dBu 0dBu +20dBu Phone jack

* 0dBu= 0.775Vrms

Output characteristics

Output terminal Actual source impedance For use with nominal Output level Connector
Nominal Max. before clip
ST OUT [L,R] 150ohms 600ohm Lines +4dBu +20dBu TRS phone jack
ST SUB OUT [L,R] 150ohms 600ohm Lines +4dBu +20dBu TRS phone jack
AUX SEND 1,2 150ohms 600ohm Lines +4dBu +20dBu TRS phone jack
EFFECT SEND 1,2 150ohms 600ohm Lines +4dBu +20dBu TRS phone jack
CH INSERT OUT 1-8 600ohms 10kohm Lines 0dBu +20dBu TRS phone jack
REC OUT [L,R] 600ohms 10kohm Lines -10dBV +10dBV RCA pin jack
PHONES [L,R] 100ohms 40ohm Lines 3mW 75mW ST phone jack
SPEAKERS 0.1ohms 4ohm Speakers 125W 500W speakON
Phone jack

* 0dBu=0.775Vrms. 0dBV =1.0Vrms

Return to Top